The 10 Best Gtx 1060 G1 Cooling Block

EK-FC GeForce GTX FE is a high-performance full-cover water block for multiple NVIDIA GeForc GTX and Titan X (Pascal) based graphics cards. This water block directly cools the GPU, RAM, and VRM (voltage regulation module) as water flows directly over these critical areas thus allowing the graphics card and it’s VRM to remain stable under high overclocks. EK-FC GeFroce GTX FE water block features a central inlet split-flow cooling engine design for best possible cooling performance, which also works flawlessly with reversed water flow without adversely affecting the cooling performance. This kind of efficient cooling will allow your high-end graphics card to reach higher boost clocks, thus providing more performance during gaming or other GPU intense tasks. Moreover, such design offers great hydraulic performance allowing this product to be used in liquid cooling systems using weaker water pumps. The base of the block is made of nickel-plated electrolytic copper while the top is made of quality acrylic material. The top also features two pre-drilled slots for 3mm LEDs. The sealing is ensured by quality rubber washers. Screw-in brass standoffs are pre-installed and allow for safe, painless installation procedure. The EK-FC GeForce GTX FE water block is backward compatible with all EK-FC1080 GTX Backplates, EK-FC1080 GTX Ti Backplates, and EK-FC Titan X Pascal Backplates. G1/4″ threaded fittings can be used on both sides of the FC terminal. Up to four EK-FC GeForce GTX FE water blocks can be used on a single ATX form factor motherboard by using EK-FC Terminal (DUAL, TRIPLE or QUAD type) system or other means of interconnectivity. Please note that EK-FC Bridge & Link system is not compatible with this water block. The EK-FC GeForce GTX FE water block is compatible with all reference design GeForce GTX 1060, GeForce GTX 1070, GeForce GTX 1080, GeForce GTX 1080 Ti, GeForce Titan X Pascal and GeForce Titan Xp based graphics cards.

Model: 3831109831977

EK-FC1080 GTX Ti FTW3 RGB is a high-performance full-cover water block for EVGA GeForce GTX 1080 Ti FTW3 based graphics cards, based on NVIDIA Pascal architecture (GP102). The water block comes with pre-installed 4-pin 12V RGB LED strip. This water block directly cools the GPU, RAM, and VRM (voltage regulation module) as water flows directly over these critical areas thus allowing the graphics card and it’s VRM to remain stable under high overclocks. EK-FC1080 GTX Ti FTW3 RGB water block features a central inlet split-flow cooling engine design for best possible cooling performance, which also works flawlessly with reversed water flow without adversely affecting the cooling performance. This kind of efficient cooling will allow your high-end graphics card to reach higher boost clocks, thus providing more performance during gaming or other GPU intense tasks. Moreover, such design offers great hydraulic performance allowing this product to be used in liquid cooling systems using weaker water pumps. The base of the block is CNC machined out of nickel-plated electrolytic copper while the top is CNC machined out of high-quality acrylic material. The sealing is ensured by quality rubber O-rings. Screw-in brass standoffs are pre-installed and allow for safe, painless installation procedure. This product is compatible with popular RGB sync technologies from all major motherboard manufacturers. The arrow marking on the 4-pin LED connector is to be aligned with the +12V marking on the RGB header. EKWB recommends the purchase of aesthetic retention backplate which improves the looks of your graphics cards and also provides some passive cooling to the circuit board VRM section. The EK-FC1080 GTX Ti FTW3 RGB water block is compatible with EK-FC1080 GTX Ti FTW3 Backplates and the factory EVGA backplate as well.

Model: 3830046996466

The world-renowned manufacturer, Alphacool, offers the Eisblock GPX a very noble and high-quality full cover water cooler for your graphics card. The Eisblock GPX is available in two versions; An eye-catching version with a plexiglass window with RGB lighting to really show off or a simple but elegant version made of acetal. Both coolers are based on an identical copper heat sink, which is completely nickel-plated. The surface area where the water flows is very large, so that all components that give off heat are actively cooled with water which increases performance. The 35 fins of the cooler are only 0.6 mm thick and cover even large GPUs completely. The large cooling surface is also ideal for graphics cards with HBM memory. Backplates for both cooler variants are included, but they differ significantly. The acetal version uses a classic backplate coated with fins for better cooling. The plexi version of the Eisblock GPX water cooler uses a smooth backplate, which together with the cooler encloses the entire PCB. This makes the cooler and graphics card look like a single unit rather than a front and back plate. The SLI connector on Nvidia graphics cards is protected by a screwed cap, which can be removed if necessary. The optical highlight of the Plexi variant, besides the very large window, of course also the complete and integrated RGB lighting. This is compatible with ASUS Aurora Sync, Biostar VIVID LED DJ, Gigabyte RGB Fusion or MSI Mystic. But pay attention to the connection on your mainboard. You may need a Male-to-Female adapter for some motherboards. With the Alphacool EisBlock GPX full cover water cooler for your graphics card you get a high-quality cooler with excellent cooling performance. You have the choice between a simple but noble black acetal version or a striking, wonderfully illuminated and chic plexi version with a large viewing window. Compatible with Nvidia Titan X (Pascal) / 1080Ti Founder’s Edition GPU cards.

Model: 11568

The Thermosphere cooling engine uses similar, yet refined as per needs of modern microprocessors, fin design as its ancestor. The cooling liquid accelerates through jet plate’s nozzle and turbulently continues its path through numerous very thin channels which provide extreme cooling surface area. EK-Thermosphere can also work flawlessly with reversed water flow which does not affect the cooling performance. Base is made of nickel plated electrolytic copper, backbone is made from laser cut brushed stainless steel plate while the top is made of quality cast acrylic material. The sealing is ensured by quality rubber washers. Screw-in brass standoffs are pre-installed in each exchangeable mounting plate and allow for safe, painless installation procedure. Block is mounted with enclosed M3x4 DIN7985 screws. G1/4″ threaded fittings can be used on both sides of the FC terminal. Up to four EK-Thermosphere water blocks can be used on a single ATX form factor motherboard by using EK-FC Terminal (DUAL, TRIPLE or QUAD type) system or other means of interconnectivity. Please note that EK-FC Bridge & Link system is not compatible with this water block. GPU compatibility: EK-Thermosphere series waterblocks supports majority of modern nVidia and AMD high-end graphics cards via exchangeable mounting plates. The product however comes factory pre-fitted with mounting plate G80 (mounting pattern 58x58mm) and ready for use on modern nVidia GeForce GTX graphics cards only. Please check compatibility at EK’s CoolingConfigurator. To use this product on AMD and other nVidia graphics cards it is mandatory to purchase additional mounting plates: – G92: 53x53mm – R600: 54x54mm – GF560: 51x61mm – G200: 61x61mm Enclosed in the box: – EK-Thermosphere series water block /w pre-installed G80 mounting plate – mounting mechanism – thermal grease (TIM) EK-Ectotherm (1g)

Thermaltake Pacific v-gtx 10 series founders Edition transparent water block is a full cover water block including an aluminum alloy back plate. Compatible with NVIDIA GeForce GTX 1080/1070 fe models, deliver the ultimate in cooling performance. Featuring 0.5mm internal fin construction, the Pacific v-gtx 10 series is manufactured with cnc machined copper base, nickel plating for ideal protection and supporting G1/4 threaded fittings. Included hardware supports users for easy installation. See the true power of liquid cooling with the Thermaltake Pacific GTX 10 series GPU water block.

Compatibilities:

Gigabyte GTX 1080 D5X 8G
Gigabyte GTX 1080 WINDFORCE OC 8G
Gigabyte GV-N1080WF2
Gigabyte GV-N1080 G1 GAMING 8GD
Gigabyte GTX 1070 G1 GAMING 8G
Gigabyte GV-N1070 WF2
Gigabyte GV-N1060G1 GAMING 6GD
Gigabyte GTX 1060 6G 9Gbps
Gigabyte GTX 1060 D5 6G

NOTE: If your graphic card model number is not included in the compatible list. DON’T purchase it as your thought.
Anyone purchases items by mistake will pay for the return postage fee.
Please feel free to contact us if you are not sure about it, just let us know and don’t worry. We will confirm it for you. Thanks.

Features:
1. Block with 0.5mm micro channel injection design, all designed only for performance!
2. Block using large flow design, even if low raise pump can use it.
3. Block made by high purity copper, and electroplating to prevent oxidation and makes beautiful.
4. Inlet and outlet can change direction free, easy to build watercooling system.

Please Pay Attention:
1. Please double check the graphics card detail model to ensure compatibility. Please feel free to contact us if you are not very sure.
2pcs G1/4 3/8″ ID 1/2″ OD Silver Compression Fittings are included, instead of the ones in the pictures.
3. The pictures are for reference only, we can only guarantee the performance and compatibility of the products, the factory can change product design at any time for the improvement of the product.
4. Prohibit the use of alcohol containing coolant.
5. Graphics card block installation requires a certain skill and experience, because the graphics card manufacturing tolerances may have a certain impact on the block installation, we can assist buyers to solve such problems, but this can not be the basis of returns.

Suitable for GIGABYTE GTX 1050 1050Ti 1060 1070 1070Ti 1080 |RX580 570 480 470|R9 390X

100% new, fine workmanship, simple sense is very strong!
Bykski N-GV1080G1-X for Pcasl Gigabyte GTX1080 G1 design,please confirm before buying graphics specific specifications, to ensure the compatibility of water cooling block.
Video card water cooling block is free to change direction, convenient players form a SLI&CF firefight system, can be in series or in parallel.
parts list:
fast twist X 2
plugs X 2
thermal paste X 1
mounting screws X 1
RGB LED X 1
Compatible graphics card type: Gigabyte GTX 1080 D5X 8G
Compatible graphics card type: Gigabyte GTX 1080 WINDFORCE OC 8G
Compatible graphics card type: Gigabyte GTX 1070 G1 Gaming 8G
Compatible graphics card type: Gigabyte GV-N1070 WF2
Compatible graphics card type: Gigabyte GV-N1080WF2
Compatible graphics card type: Gigabyte GV-N1080 G1 GAMING-8GD
Compatible graphics card type: Gigabyte GV-N1060G1 GAMING-6GD
Compatible graphics card type: Gigabyte GTX 1060 6G 9Gbps
Compatible graphics card type: Gigabyte GTX 1060 D5 6G
NOTE: If you are unsure whether compatible, please contact the seller or view graphics brands and models, because the description have mentioned writing compatible graphics card name and model number .

Gigabyte GeForce GTX 1060 G1 gaming video card power by GeForce GTX 1060, integrated with 6GB GDDR5 192bit memory, windforce 2x with blade fan design. Supports up to 8K display at 60Hz. 16.8M customizable Color RGB lighting.

Conclusion

By our suggestions above, we hope that you can found gtx 1060 g1 cooling block for you.Please don’t forget to share your experience by comment in this post. Thank you!